..:: Linux CaPhede ::..

Linux itu Mudah

Configurasi Wvdial “TravelMate 2420”

Posted by firstly pada Juli 12, 2007

Hi, here is short tutorial to set up your Linux OpenSuse 10.2 and Ubuntu 7.4 get connect to CDMA modem to get internet access. I use Nokia CDMA 2116 and DKU-5 (not original) cable data. For the internet provider i use Starone.

1. Log on as root (administrator)
2. Connect Nokia CDMA 2116 and DKU-5 to usb port
3. Open Konsole and type dmesg, on my computer ( i use laptop Acer Travelmate 2420) you will find
something like this

usb 1-1: ark3116 converter now attached to ttyUSB0

This is mean that your Linux OpenSuse 10.2 recognize your Nokia CDMA 2116 modem and the DKU-5
cable data

4. Then type “wvdialconf /etc/wvdial.conf”. Find someting like this :

Found a modem on /dev/ttyUSB0.
Modem configuration written to /etc/wvdial.conf.
ttyUSB0: Speed 230400; init “ATQ0 V1 E1 S0=0 &C1 &D2″

5. Ok, now open the wvdial.conf (i use kwrite) and make some change on this :

Modem = /dev/ttyUSB0 —-> fill based on information on step 3
Baud = 230400 —-> fill based on information on step 4
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 —-> fill based on information on step 4
Init3 = AT+cso=33 —-> if blank, fill with AT+cso=33
Area Code =
Phone = #777 —-> if you are in indonesia and use CDMA type #777
Username = starone —-> ask your phone/internet provider
Password = indosat —-> ask your phone/internet provider
Ask Password = 0
Dial Command = ATDT
Stupid Mode = 1
Compuserve = 0
Force Address =
Idle Seconds = 300
DialMessage1 =
DialMessage2 =
ISDN = 0
Auto DNS = 1
Modem Type = Analog Modem

6. Save your change and exit

7. Open the konsole again and type wvdial

8. The connection work fine if you find information like this :

CONNECT
~[7f]}#@!}!}!} }3}”}&} } } } }#}%B#}%}’}”}(}”W}0~
–> Carrier detected. Starting PPP immediately.
–> Starting pppd at Sun May 20 17:34:43 2007
–> pid of pppd: 4547
–> Using interface ppp0
–> pppd: #777
–> pppd: #777
–> pppd: #777
–> pppd: #777
–> pppd: #777
–> local IP address 10.242.30.198
–> pppd: #777
–> remote IP address 10.64.64.64
–> pppd: #777
–> primary DNS address 202.93.40.174
–> pppd: #777
–> secondary DNS address 202.155.0.10
–> pppd: #777
–> Script /etc/ppp/ip-up run successful
–> Default route Ok.
–> Nameserver (DNS) Ok.
–> Connected… Press Ctrl-C to disconnect
–> pppd: #777

I hope this information also work with your Linux. 🙂

NB.

wvdial: carrier signal lost

Iklan

Tinggalkan Balasan

Isikan data di bawah atau klik salah satu ikon untuk log in:

Logo WordPress.com

You are commenting using your WordPress.com account. Logout / Ubah )

Gambar Twitter

You are commenting using your Twitter account. Logout / Ubah )

Foto Facebook

You are commenting using your Facebook account. Logout / Ubah )

Foto Google+

You are commenting using your Google+ account. Logout / Ubah )

Connecting to %s

 
%d blogger menyukai ini: